i sprayed white grease on the ends, still makes noise. I got the upper control arm replaced and I have the lower removed, but the lower control arm still has the torsion bar stuck in it. an help would be great. Remove anchor from torsion bar.

will takin a torch to the a-arm to losin them up or am i makin it worse. do i have to remove them to better grease the ends? This easy-to-use tool he Im trying to figgure out how exactly im going to get the torsion bar off without killing myself.

Here is Dodge procedures . torsion bar adjuster bolts. click link below . how to replace a torsion bar on a 2002 dakota 4wd .

Got the torsion bars unscrewed, lower ball joints popped loose in the knuckles, shocks loose at their lower ends and took off the sway bar. You will only get about 1.5" of lift by doing that. REMOVAL (1) Raise and support the vehicle with the front suspension hanging. The big difference is the fact that the durango was MUCH heavier than even a fully loaded quad cab, thus the need for bigger t-bars. Remove the torsion bar in a dodge ram? (Sway bar bushings are shot too.

RE: Torsion Bar Differences IP: Logged Message: That was me. I've been banging on it and spraying it with WD40 and even some Deep Creep and it's … From: Message: pwhiteelec05 GenI 10/21/2007 19:03:50: Subject: torsion bar replacement IP: Logged Message: tryin to replace bars on my 97 dak 4x4 sport. Jump to Latest Follow ... but some anti-sieze on the hex ends of the torsion bars to make getting it out the next time (if there is a next time) alot easier. Please keep in mind Just Answer is set up on an honor system. What are the advantage and disadvantage of orthopneic position. soaked the f out of them and beat the heck out of them but the wouldnt move a bit. James: FortWorth4x4 GenIII 11/11/2002 13:52:31: RE: Torsion bar Lift IP: Logged Message: About as hard as it is to turn the bolts. I have sent the information you have requested & have answered . now, if somebody could do a coilover/coil spring swap, and document it on here, I'd love them forever.

3rd Gen Ram Tech - removing torsion bar - Im installing a keyway lift on my 03' 4x4 1500. This durable, solid-steel tool makes it easy to load and unload torsion keys without damaging the torsion bar or your hands! (4) Remove torsion bar and anchor. 99 4x4 95,000 miles. could be tough.

if your re using them then don't knick the bars and use the removal tool or something similar, if not using the bars over you can just stick a set of vice grips or something on them and bang the bars out. 1999 dodge dakota 4x4 v8. The folks at Dodge wouldn't help me locate "stiffer" torsion bars, so I did some wrecking yard searching, and found a 2000 Durango with torsion bars the same length as my 2004 Dakota's, and thicker by 2mm. ... A forum community dedicated to all Dodge Dakota and Durango owners and enthusiasts. 3) Remove the adjustment bolt from swivel. TORSION BAR . Subject: Torsion bar Lift IP: Logged Message: How hard is it to do a torsion bar lift.

NOTE: Count and record the number of turns for installation reference. In theory, the torsion bars should swap over with the torsion bar mounts and the lower control arms from said Durango. the torsion bar all the way through to remove it. PLEASE click ACCEPT so that I … Well just the drivers side one right now but i'm pretty sure the other one will start soon. 3) remove torsion bar retaining clip at rear of bar 4) slide the torsion bar out the rear of the cross member.

5). Unanswered Questions. (2) Turn the adjustment bolt counterclockwise to release spring load (Fig.